乐高42083--布加迪灯光安装教程

布加迪遥控灯组

灯组包含：A组车头灯、B组室内灯.发动机、C组车尾灯、

D尾翼灯车牌灯、E组底盘灯。遥控器、接收板、锂电池、

充电线

1.首先取出A包，按照图片把车头灯的零件拆出，然后按

照以下图片安装即可。

Lego 42 08 3- -Bu gatti L ight I ns ta llation T ut or ial

B ugatti Remo te Co nt rol Light Set The lamp group

i ncl ud es : A gro up hea dligh ts , B gro up i nd oor

li ghts.E ng ine, Group C rear lights, T he D

ta ilwing ligh t lic en se plate light , th e E group

chass is li gh t.Remo te c on trol, recei vi ng bo ard,

lithi um b at tery, Chargi ng li ne

T he 1 . fir st r em ov es the A pac kage, remov es t he

headligh t par ts f ol lowin g the pict ur e, an d th en

presses Inst al l it in th e pi ct ur e below.

取出车头灯条，撕开背面白色的胶纸粘贴在前灯的零件部位

上，然后用镊子按紧灯直到紧贴大灯底部安装完成，复原车

头并将线头导到到室内

Re mo ve the h ea dlight str ip , tea r the w hi te tape

on th e bac k an d pas te the parts of th e he adligh t

On , th en press the lamp with tweez er s unt il

ins ta lled close to the bottom of the head li gh t

to res to re t he ca r Hea d an d gui de the thread head

to th e ro om

2.按照图片所示把零件拉开，然后把整个盖子翻上，如图所示

2. pulls the part as shown in the picture and then flip the entire

cover as shown

取出灯组B和发动机盖子，将末端灯片贴在盖子下方。

剩余灯组穿到室内，贴于室内顶部如图所示。端子口接到接收板B口

Re move the light s et B and engine lid and attac h

t he end light und er th e li d.

Th e re mainin g lig ht g ro ups are wo rn indoors a nd a ff ix ed

to t he to p of th e cha mb er as sho wn in Fi g.Termin al po rt

is conne ct ed t o the r ec eiving board B port

取出C组灯，将尾灯配件拆下

R em ove the group C li ghts and remove th e tail li ght fittin gs

灯片贴到左右两侧，复原尾部将线头穿回室内端子口接到接收板C口

St ick to th e lef t an d ri ght sides, r esto re t he re ar w ill

wear the wire b ack to the indoo r ter mi nal port to the

port of the receivi ng bo ar d C

取出D组灯片，将第一片灯组贴到尾翼下方。

第二片灯组贴到布加迪标顶部

Remove t he D set light and post the first l ig ht s et

below the tail.

Th e sec on d la mp set is p ost ed to th e to p of the B ug at ti logo

复原车子盖板

Restore t he ca r co ve r pla te

取出E组灯，拆下车头配件

将E组灯的单片灯贴到配件中间，线头留到左侧。

R em ove th e gr oup E li ghts and remove the head fit ti ng s

Po st th e E lam p to the midd le of the acc ess ory and

l ea ve the th read to the left.

复原配件后将车子翻过来，安装底盘氛围灯

Rep ai r th e acc essori es an d tur n th e car o ve r to

ins ta ll th e ch assis atmosp he re light

将线头穿回室内 拆下车尾排气口，将最后一组灯片贴到指定位置

复原排气口

We ar th e li ne ba ck i ndoors to remove the rear exha us t and

p ost the last set of li ghts to the specifi ed lo ca tion

Resum e ex ha ust po rt

线头端子口接到接收板，装上锂电池、灯组安装完成

The cabl e ter mi nal port is connected t o the rece ivi ng

bo ard an d in stalle d wit h li th ium battery and lam p set

将线整理下藏到车座后方，

Collec t the line to the car behin d the s ea t,

注意：接收板藏太深可能会影响遥控的控制噢

电池充电

B at tery chargi ng