http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn
http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn
http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn
http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn
http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn
http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn
http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn
http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn
http:/ /cctiw.canon.com.cn http:/ /cctiw.canon.com.cn
8.错误/卡纸/警告
329
E002-0003- 定影副热敏电阻(前)开路检测错误
检测描述 当定影加热器打开直到 PI 控制启动时,定影副热敏电阻(前)检测到温度低于 40 摄氏度超过 3
秒以上.
对策措施 [相关零件]
- 连接 DC 控制器电路板 (UN50/J121)和定影热敏电阻(TH01)的线束
- 连接 DC 控制器电路板(UN050/J115) 和低压电源电路板 (UN48/J322)之间的线束
- 连接低压电源电路板 (UN48/J302)和 AC 连锁开关(SW12)之间的线束
- 定影组件
- 低压电源电路板 (UN48)
- DC 控制器电路板 (UN50)
[对策措施] 检查/更换相关的线束/电缆、插头和零件.
执行对策措施工作以后, 完成下列操作以清除错误: COPIER> FUNCTION> CLEAR> ERR.
[参考] 更换 DC 控制器电路板之前, 备份维修模式数据并在更换之后恢复备份的数据以便可以保
护数据.
- 备份: COPIER> FUNCTION> VIFFNC> STOR-DCN
- 恢复: COPIER> FUNCTION> VIFFNC> RSTR-DCN
E002-0004- 定影副热敏电阻(后)开路检测错误
检测描述 当定影加热器打开直到 PI 控制启动时,定影副热敏电阻(后)检测到温度低于 40 摄氏度超过 3
秒以上.
对策措施 [相关零件]
- 连接 DC 控制器电路板 (UN50/J121)和定影热敏电阻(TH01)的线束
- 连接 DC 控制器电路板(UN050/J115) 和低压电源电路板 (UN48/J322)之间的线束
- 连接低压电源电路板 (UN48/J302)和 AC 连锁开关(SW12)之间的线束
- 定影组件
- 低压电源电路板 (UN48)
- DC 控制器电路板 (UN50)
[对策措施] 检查/更换相关的线束/电缆、插头和零件.
执行对策措施工作以后, 完成下列操作以清除错误: COPIER> FUNCTION> CLEAR> ERR.
[参考] 更换 DC 控制器电路板之前, 备份维修模式数据并在更换之后恢复备份的数据以便可以保
护数据.
- 备份: COPIER> FUNCTION> VIFFNC> STOR-DCN
- 恢复: COPIER> FUNCTION> VIFFNC> RSTR-DCN
E003-0004- 定影主热敏电阻低温检测错误
检测描述 当从 PI 控制启动直到最后旋转结束(定影加热器关闭)时,定影主热敏电阻检测到温度低于 80
摄氏度超过 1 秒.
对策措施 [相关零件]
- 连接 DC 控制器电路板 (UN50/J121)和定影热敏电阻(TH01)的线束
- 连接 DC 控制器电路板(UN050/J115) 和低压电源电路板 (UN48/J322)之间的线束
- 连接低压电源电路板 (UN48/J302)和 AC 连锁开关(SW12)之间的线束
- 定影组件
- 低压电源电路板 (UN48)
- DC 控制器电路板 (UN50)
[对策措施] 检查/更换相关的线束/电缆、插头和零件.
执行对策措施工作以后, 完成下列操作以清除错误: COPIER> FUNCTION> CLEAR> ERR.
[参考] 更换 DC 控制器电路板之前, 备份维修模式数据并在更换之后恢复备份的数据以便可以保
护数据.
- 备份: COPIER> FUNCTION> VIFFNC> STOR-DCN
- 恢复: COPIER> FUNCTION> VIFFNC> RSTR-DCN