兰博基尼SIAN闪电 遥控灯光灯组包含：
A组车头灯、B组室内灯.发动机、C组车尾灯、D尾翼灯、
E组车低灯 遥控器、接收板、锂电池、充电线
兰博基尼SIAN闪电 遥控灯光
The Lamborghini SIAN Lightning Remote Control Lights
The Lamborghini SIAN Lightning Remote Control Light
Light Set includes: Group A headlights and group B
indoor lights. Engine, Group C taillights,
D taillights, Group E car low light remote control,
receiving board, lithium battery, charging line
A组车头灯
要把箭头的位置两个车头灯模块拆下
Group A headlights
Remove the two headlight modules from the arrow position
首先将左右两边绿色的软管拔出向上推起
First, pull out the green hose on the left and right sides
and push it up
接下来把手往黄圈位置下面把整个车头灯模
块的向上顶起
Next, put the entire headlight mold under the yellow ring
position Up the block
同样方法，将左右两侧的车头灯模块逐一拆下
In the same way, remove the left and right headlight modules
one by one
全部拆下的零件，一览如下
接下来拆下黄圈的黑色零件
All the removed parts are listed below
Next, remove the black parts of the yellow ring
拆下零件如下
取出A包两个灯饰的灯条，第一个灯饰零件
先安装在右边拆下的零件上
Remove parts as follows
Take out the lamp strips of two package A and the first
lighting part Install on the parts removed on the right first
将第一个安装好的零件从箭头孔臂中间穿过
Pass the first mounted part through the middle of the
arrow hole arm
将线压在下面，复原黑色零件
Press the line below to restore the black parts
左边也是同样的安装方法
The same installation method is also found on the left
中间连接的线太才可以在插栓上面缠绕一圈
下的两个前车灯模块，准备安装灯饰
The line in the middle can be wrapped around the bolt
Under the two headlight modules, ready to install the lighting
如下图所示拆下右前车灯的零件
将三个白色的棍子拆下
Remove the right front headlight parts as shown in
the figure below
Remove the three white sticks
把黄圈的黑色两个零件拆下
Remove the two black parts of the yellow ring
右前车灯拆下的零件如下
The removed are as follows
首先取出配送的黑色零件
将十字头插入刚才拆下的两个零件的位置
First remove the black parts
Insert the crosshead into the position of the two parts
that you have just removed
然后取出蓝色灯饰零件按照下图的顺序安
装在零件上
Then take out the blue lighting parts in the sequence of
the figure below Pit on parts
第四个蓝色灯饰零件准备安装在左前灯上
取出左前车灯跟刚才一样拆下白色的零件
A fourth blue lighting part is ready to be installed on
the left headlight
Remove the left front headlight and remove the white
parts as before
从第个蓝色灯饰零件按照上面的顺序开始安装起
Start with the first blue lighting part in the order above
黑色零件替换上去
Replacing the parts in black
装好灯饰零件如下图所示
取出6条透明软管
Install the lighting parts as shown in the figure below
Remove the 6 transparent hoses
插入6个蓝色灯饰零件上
透明软管长的可以自己用剪刀对比一下长
度剪好比例
Insert on the 6 blue lighting parts
Transparent hose long can be their own scissors to
compare the long Cut the proportion
先从右前车灯复原
Recovery from the right front light first
把连接两个大灯线路往中间穿过效果
如图所示，将插头线留在左边
Connect the two headlight lines to the middle through
the effect Leave the plug line to the left, as shown
导线穿向红色箭头方向
B组室内灯跟发动机灯室内灯贴于方格处
The wire runs through the red arrow
Group B indoor lights and engine lights indoor lights
affixed to the square
B组室内这里有二个版本的安装方法，请看下您
拿到手上的是哪一款。新款 （灯条从室内穿出
，一整条贴于主轴上。下图电击放大。）
Group B indoor here are two versions of the installation method,
please see you Which one did you get it with it.New style (light
strips wear from the room A whole stick is attached to the main
shaft.Below for shock amplification.）
第二种（室内灯出来是二节灯，贴于两边翼上）
Second (indoor lights out are two lights, posted on both wings)
C/D组
C/D group
E组车底灯
Group E car bottom lamp
